Skip
Free domestic shipping over 15,000 yen | FREE DHL SHIPPING WORLDWIDE FOR ORDERS 50K+ yen : Details
Free domestic shipping over 15,000 yen | FREE DHL SHIPPING WORLDWIDE FOR ORDERS 50K+ yen : Details

Intellijel Designs Tete

¥53,900 (Tax excluded ¥49,000)
Expander that adds loop and sequencer functionality to Tetrapad

Format: Eurorack
Width: 8HP
Depth: 39mm
Current: 120mA @ + 12V, 6mA @ -12V

For the latest Intellijel manuals and firmwareManufacturer support pageSee also

In stock. Orders made by 15:XNUMX will be shipped the same day

MUSICAL FEATURES

TeteTetrapadThis is an expander module that allows you to capture and save the movements of and perform loops and sequences. You can use the synchronization and modulation functions with the clock to add various changes.

In a Tetrapad equipped with Tete, Tete acts as the master module and Tetrapad acts as its control surface, which behaves differently than when it was used alone. There are three modes, and one of them works.
 
  • Voltage Mode: In this mode, a combination of 8 output voltages can be selected from up to 16 grids on the Tetrapad. You can also record which grid you select and loop that movement later. By assigning the CV input of Tete, you can control the X / Y coordinates of the grid and perform a Cartesian sequence. The change can be smoothed through the output CV.
  • Notes Mode: This mode allows you to create sequences and loops using chords, scales, and keyboard. The grid can be divided into 4/12/16 scales, and loops, transposes, chord inversions, etc. can be controlled with CV to make changes in real time. In Sequencer mode each step can be set as a tie, a rest, or a 25/50/75% length gate. This feature allows you to create musical chord sequences very quickly and intuitively.
  • Combo Mode: Each of the 8 outputs can be individually assigned to a fader (unipolar / bipolar), crossfader, Euclidean sequencer, toggle switch, or LFO, and all movements are recorded continuously (not on steps) and looped. Will be done.
Other features are as follows.
  • Step Recording can record Tetrapad performance up to 256 steps
  • Real-time continuous recording of Tetrapad performance. The time is limited only by the size of the microSD, but the recording time that can be comfortably controlled by the Tete interface is about 5 minutes
  • Smart overdub yesterday to detect touch and start recording
  • Transport control convenient for linking with other modules
  • The three CV outputs can be assigned signals by the user. For example, assigning the ACV output to a position outputs a voltage that indicates the position in the loop or sequence, which is convenient for linking with Planar3 etc.
  • The three CV inputs with Attenuverter allow the user to assign modulation destinations. You can also assign two gate / trigger inputs and a clock input.
  • Works with both internal and external clocks, clock divides and multiplications are possible in either case
  • You can easily check the internal state by the screen
  • Since the pad can be divided into 2,3,4, 16 and 16, you can select up to XNUMX voltage banks (Voltage mode) and XNUMX scales (Note mode).
  • 99 presets are available for each mode and all parameters, modes and CV assignments are recorded
  • The last state is automatically recalled when the power is turned on. Please note that the state is not automatically saved only while the looper or sequencer is running.

firmware Update

Follow the steps below to update the firmware.
  1. Power down the module
  2. Connect the USB cable from the back of the module to your computer.
  3. IntellijelPagesOpen the updater downloaded from and select the module and version from the dropdowns.
  4. SETUP and REC (•)Hold down the button and power cycle the module.
  5. At the bottom of the updaterUpdateWhen the button is pressed, the progress bar starts, and when the message “Update completed successfully” is displayed at the end, the update is complete.
  6. Restart the modular and it should work with the new firmware

Top
x